INSTRUCTION MANUAL BLACKHAWK SERIES BROADBAND POWER SUPPLIES Installation and Operation Manual Manual Part No:017-027-B0 Issue 01 (01
As shown in Fig. 2-1, output voltage never decreases below 90% of full output rating during the source transfer. Output voltage recovers to full rate
Missing or Damaged Items If items are found to be damaged or missing, contact the shipping company and your Multilink Broadband representative immedi
conductors shall be connected to the power supply through an appropriate service entrance equipment. Permission to mount the UPS on the utility pole
General Installation Procedure: Ground Mounted Cabinet The following procedure is intended as a general guideline only for ground-mounting a cabinet
5. INSTALLATION NOTE: Do not install batteries until verifying that the cabinet mounting hardware is secure. Failure to do so may result in the cabin
CABINET INDICATORS: Mini Mate-N-Lok: connects the enclosure alarm and status lamps to the power supply for external status indication. The power sup
Section 5: Installation and Setup Installing and wiring any model within the Blackhawk Series power supplies into an enclosure may be accomplished
The power supply should be mounted on a ventilated shelf that allows free air circulation, especially through the front and rear panels on the right s
4) Connect the AC line cord from the power supply to the appropriate AC receptacle. 5) Insert the battery plug from the battery wiring harness into
Battery Installation Procedure: 1. Place the batteries on the lower shelf of the enclosure, positive terminal facing out. 2. Route the terminal co
Documented Power Supply Models The following power supply models, with their part numbers, are documented by this instruction manual. For available
Section 6: Startup and Operation The power supply is ready to be placed into operation after it has been installed in its enclosure and all input
Front Panel Status Indicators: Verify the status of the power supply from the LED display during normal operation. All indicator LEDs are located on
1. Operate the toggle of the BATTERY CIRCUIT breaker to the OFF position, then disconnect the battery cable from the power supply. 2. Disconnect t
Battery Balance Manager: This accessory, available as a separate assembly, is designed to maintain identical terminal voltage of each 6-cell battery
YELLOWBLUETB1 TB2ORANGEWH / BKBK / WHWHITEBLACK90V75V60VOUTPUT VOLTAGESELECT WIRETRANSFORMERINPUT POWERWIRE (WHITE)INPUT POWERWIRE (BL
DANGER Performing the following procedure exposes the servicing technician to hazardous voltages and will disrupt power to the system loads. The ser
DANGER Performing the following procedure exposes the servicing technician to hazardous voltages and will disrupt power to the system loads. The ser
INDICATES JUMPERCONNECTED OVERDESIGNATED PINS864231 5784261240V SETTING735700-064-21OUTPUT INTERFACEPCB ASSEMBLY700-064-20J1T1J10RELAY K2INSTALLED HER
performance reporting, the entire inverter module should be changed in the field. The module with suspected problems should be returned to a service
Section 10: Specifications Black Hawk 600-120/60-36 or 600-120/60-48 AC Input Voltage ……………………… 120 volts AC, nominal Nominal Input Voltage
1350 VA OUTPUT RATING MODEL NUMBER PART NUMBER INPUTS 1350-120/60-36 017-030-20 120VAC, 60Hz, 3-Battery
Specifications (cont’d) Black Hawk 900-120/60-36; 900-120/60-48; 900-240/60-36; 900-240/60-48 AC Input Voltage ……………………… 120 volts or 240 volts A
Specifications (cont’d) Black Hawk 1350-120/60-36; 1350-120/60-48; 1350-240/60-36; 1350-240/60-48 AC Input Voltage ……………………… 120 volts or 240 vol
Table of Contents Blackhawk Series Broadband Power Supply Section 1: Critical Safety Issues………………………………………….….5 Safety Admonishments Emergency
Section 9: Maintenance and Adjustments ...…….….……23 Preventive Maintenance Output Voltage Reconfiguration Input Voltage Configura
Emergency Shutdown Procedure DANGER Exercise extreme caution when performing the following procedure. Carry out the steps precisely in the order g
Safety Issues of Power Supply Installation and Use The subject power supply has been designed and built to power CATV and broadband distribution equi
cannot be attained, a suitable forced-air cooling system may be required within the cabinet. Battery Safety Issues When installing batteries for the
Section 2: lntroduction Blackhawk Series Product Overview The MultiPower Blackhawk Series power supplies provide filtered and regulated AC output
Comments to this Manuals